Expert boiler repair in Franklin, TN. NATE-certified technicians, quality equipment, and results you can count on.
Boiler systems serving Franklin, TN homes require specialized knowledge of water chemistry, expansion tank pressure, flue gas analysis, and aquastat sequencing. KIC Refrigeration delivers professional boiler repair that addresses kettling, air-bound radiators, leaking seals, and control board failures with the expertise your hydronic system demands.
Franklin homeowners and businesses count on reliable boiler repair to maintain comfort and protect indoor air quality. Serving a city of 91,635 across Tennessee, KIC Refrigeration brings the experience and crew depth to handle boiler repair projects of any scale. We begin every job with an honest evaluation and a clear, written estimate.
Our boiler repair technicians in Franklin, TN are NATE-certified, EPA 608 licensed, and equipped with advanced diagnostic tools. From the initial inspection through final commissioning, we maintain open communication and hold ourselves to the highest standards. That is how KIC Refrigeration has earned the trust of homeowners across Tennessee.
A clear, step-by-step approach to every boiler repair project we take on.
Our Franklin technician begins with a comprehensive safety inspection — testing the pressure relief valve, low-water cutoff, high-limit control, gas valve operation, and flue draft. We check boiler pressure, inspect the expansion tank, and look for signs of corrosion, leaks, and scale buildup.
We use a combustion analyzer to measure flue gas temperature, CO levels, O2 percentage, and stack draft. These readings tell us if the burner is firing efficiently or if the heat exchanger, burner assembly, or gas valve needs attention.
KIC Refrigeration repairs boilers in Franklin, TN with the correct parts and procedures. We match components to your specific boiler model and BTU input rating, torque all gas connections to spec, leak-test with gas detector soap, and verify the repair restores proper operation and efficiency.
Our Franklin crew pressurizes the boiler system to 15 to 20 PSI, inspects every fitting and valve for leaks, bleeds air from all zone circuits, and runs the boiler through a full cycle — verifying ignition, flame signal, circulator operation, and temperature rise to confirm the repair.
Common questions about boiler repair costs, timelines, and what to expect.
Boiler repair in Franklin typically costs $200 to $700 for common component failures like thermocouples, aquastats, zone valves, circulator pumps, and expansion tanks. Ignition control module or gas valve replacement runs $300 to $800 depending on the boiler manufacturer. Heat exchanger replacement is the most expensive repair at $1,500 to $4,000, varying by boiler type — cast iron sectional, copper fin tube, or stainless steel condensing — and BTU input rating. KIC Refrigeration provides a detailed written estimate with itemized parts and labor costs before beginning any boiler repair at your Franklin property so you can make an informed decision.
Boiler pressure loss indicates a leak somewhere in the sealed system. The most common causes are a failed expansion tank bladder that allows air into the system, leaking zone valve packings, corroded pipe fittings or baseboard connections, a weeping pressure relief valve, or a pinhole leak in the heat exchanger itself. A healthy hydronic system holds 12 to 18 PSI when cold and rises to 18 to 25 PSI at operating temperature. If the pressure gauge drops below 10 PSI, the low-water cutoff should shut the burner down to prevent damage. KIC Refrigeration pressure-tests the system, inspects all fittings and valves, and locates the leak at your Franklin home so we can repair it permanently.
The repair-versus-replace decision depends on your boiler age, AFUE efficiency rating, and the cost of the current repair. If the boiler is under 15 years old and the repair is under $2,000, repairing usually makes financial sense. Cast iron boilers over 25 to 30 years old with cracked sections, or standard-efficiency units with AFUE ratings below 80 percent, are typically better replaced with a new high-efficiency condensing boiler rated 90 to 98 percent AFUE. A condensing boiler extracts latent heat from flue gases that older boilers waste up the chimney, saving 15 to 20 percent on annual fuel costs. KIC Refrigeration provides honest repair-versus-replace assessments for Franklin homeowners based on equipment condition rather than sales targets.
Warning signs that your boiler needs professional attention include radiators or baseboard that heat unevenly or stay cold in certain zones, banging or kettling noises caused by scale buildup or air in the system, the pressure gauge reading below 12 PSI or above 25 PSI, visible water leaks at fittings, valves, or the boiler itself, a pilot light or electronic ignition that will not stay lit, error codes flashing on the control board, and a noticeable increase in gas bills without a change in thermostat settings. Any of these symptoms warrants a professional inspection. KIC Refrigeration diagnoses boiler problems in Franklin quickly using combustion analyzers, pressure testing, and electrical diagnostics to identify the exact failure.
What our customers say about working with our HVAC team.
"Mini split installation went smoothly. Clean work, no mess left behind. Would have liked a bit more explanation on the maintenance schedule but overall very happy."
"Furnace tune-up was straightforward and the technician was friendly. Gave some tips on filter replacement schedules which was helpful."
"Had a smart thermostat installed and the tech took the time to walk me through every feature and set up the app on my phone. Really appreciated that."